{"id":463,"date":"2009-08-21T02:05:49","date_gmt":"2009-08-21T07:05:49","guid":{"rendered":"http:\/\/www.rpwoodwork.com\/blog\/?p=463"},"modified":"2013-04-19T23:28:42","modified_gmt":"2013-04-20T04:28:42","slug":"high-end-drawers-part-5-dovetailing-tips-for-drawer-making","status":"publish","type":"post","link":"https:\/\/www.rpwoodwork.com\/blog\/2009\/08\/21\/high-end-drawers-part-5-dovetailing-tips-for-drawer-making\/","title":{"rendered":"High-end drawers, part 5: dovetailing tips for drawer making"},"content":{"rendered":"

\"\"<\/a><\/p>\n

A full discussion of dovetailing is beyond the scope of this series, but here are several tips<\/strong> pertaining to drawer making.<\/p>\n

Much of the success of dovetailing depends on accurately transferring the outline<\/strong> of the tails to the pin board (or vice-versa, if that is your preference). The bottom edges served as references when fitting the front and shooting the sides square, and continue that role as a heavy, flat board, squared to the front piece, aligns the sides to the front while marking for the pins.<\/p>\n

Angles for short dovetails<\/strong> should be steeper than usual to improve their appearance and possibly their strength.\u00a0The tails\u00a0for these drawers are approximately 5:1 slopes<\/a>. My usual ratio for medium to larger joints in hardwoods is 7:1.<\/p>\n

Layout the joints\u00a0so the groove for the bottom<\/strong> will be fully within the lowest tail at the front. At the back end, there is a large tail at the bottom which also fully contains the groove, while a tail at the top allows for a neat chamfer.<\/p>\n

\"\"<\/p>\n

The grooves<\/strong> to fit the drawer bottom are cut after dry fitting the front and sides and ensuring that the reference edges (the bottom edges) are aligned. For these drawers, I made the grooves 1\/4″ wide, barely 3\/16″ deep, and 3\/8″ away from the edges. Keep the grooves sufficiently shallow and away from the edges to avoid weakening the sides, though not so shallow as to allow the bottom to slip out if it\u00a0distorts a bit.<\/p>\n

Note that the bottom edge of the back piece does not end with a customary squared pin.<\/strong> The little shoulder below the lowest pin allows the bottom of that pin to have an angled surface which has contact through the full depth of the side piece. A squared pin lacks the added strength of the angle, and contacts the side piece only in the thickness remaining lateral to the groove depth.<\/p>\n

\"\"<\/p>\n

I prepare the back piece slightly wide at its bottom, cut the joints, loosely dry-assemble the joints, then mark the back piece so I can plane it, after disassembly, to align with the top of the grooves. This method separates the process of dovetailing from aligning<\/strong> the bottom edge of the back with the groove, affording more control<\/strong> in workmanship, as well as making stronger joints<\/strong>.<\/p>\n

Next:<\/strong> adding the false front and fitting the drawer. Stay with me<\/a>, we’re getting to the cool part.<\/p>\n","protected":false},"excerpt":{"rendered":"

A full discussion of dovetailing is beyond the scope of this series, but here are several tips pertaining to drawer making. Much of the success of dovetailing depends on accurately transferring the outline of the tails to the pin board (or vice-versa, if that is your preference). The bottom edges served as references when fitting […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[5],"tags":[23],"class_list":["post-463","post","type-post","status-publish","format-standard","hentry","category-techniques","tag-high-end-drawers-series"],"_links":{"self":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/463","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/comments?post=463"}],"version-history":[{"count":5,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/463\/revisions"}],"predecessor-version":[{"id":2311,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/463\/revisions\/2311"}],"wp:attachment":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/media?parent=463"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/categories?post=463"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/tags?post=463"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}