![\"\"](\"https:\/\/www.rpwoodwork.com\/blog\/wp-content\/uploads\/2009\/08\/img_1398_edited-2.jpg\" "\\"img_1398_edited-2\\"")
<\/p>\n<\/p>\n
The first, most critical step in making this type of drawer is sizing the front<\/strong>. The drawers in this project are about 14 inches wide, 3-4 inches high, and 12 inches deep. For the fronts, stock is face jointed and thicknessed to about \u00bd inch. “False fronts” will be applied later to bring the final thickness to about 11\/16 inch. (The methods described here\u00a0are applicable whether false fronts or customary half-blind dovetails are used.) Each piece is ripped to a hair less than the height of its housing and crosscut to slightly larger, about 1\/32 inch, than the housing width.<\/p>\n Unplug the machinery<\/strong>. The following hand planing is best done with a shooting board. [Here is my shooting board <\/a>and how I use it for end grain on any size board and for long grain edges on small boards<\/a>.]<\/p>\n First, the<\/strong> bottom reference edge<\/strong> of the drawer front is planed straight and square and identified with a mark. Then the left end<\/strong> is shot to match the left side of the opening. Progress is tested by offering up the piece to the housing, resting it on its bottom, and checking the left edge. (Photo, above.)<\/p>\n Now it\u2019s time to get very careful. This step is probably the most important point in your drawer\u2019s success. Bit by bit, the right end<\/strong> of the drawer front is shot so it just barely<\/em> makes it into the width of the housing. It should be snug!\u00a0<\/p>\n Finally, the top edge<\/strong> is planed so it comfortably fits in the height of the opening and is parallel to the upper edge of the opening. By keeping this gap small, 1\/32-1\/64 inch, it is easy to detect any deviation from parallel by eye. Note that the top and bottom edges of the drawer front are not necessarily exactly parallel to each other at this point because the piece has been fit directly to its opening.<\/p>\n This is incremental work<\/strong>. It is nice if the drawer opening is a perfect rectangle but this is not assumed. Any deviations are accounted for by fitting each drawer front to match its opening. With this method, errors do not compound<\/strong> as the project progresses. The drawer front prepared in this way is now the reference for constructing the entire drawer.<\/p>\n I do not make the height<\/strong> a snug fit as is sometimes taught. I believe that is a waste of effort since the finished solid wood drawer must not fit tight in height because it will bind when the humidity rises. The “air tight” drawer<\/strong>, in my opinion, makes no sense; it won\u2019t work. I also do not shoot the front to produce tapered edges for fitting in its opening, because I want to work with square reference edges when I cut the joinery.<\/p>\n Once you have thoughtfully prepared the case<\/strong> and fit the drawer front<\/strong> accurately, there is not much left from here on that is at high risk of going wrong, as long as you are patient.<\/p>\n Next:<\/strong> making and joining the sides and back.<\/p>\n","protected":false},"excerpt":{"rendered":" The first, most critical step in making this type of drawer is sizing the front. The drawers in this project are about 14 inches wide, 3-4 inches high, and 12 inches deep. For the fronts, stock is face jointed and thicknessed to about \u00bd inch. “False fronts” will be applied later to bring the final […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[5],"tags":[23],"class_list":["post-450","post","type-post","status-publish","format-standard","hentry","category-techniques","tag-high-end-drawers-series"],"_links":{"self":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/450","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/comments?post=450"}],"version-history":[{"count":5,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/450\/revisions"}],"predecessor-version":[{"id":2313,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/450\/revisions\/2313"}],"wp:attachment":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/media?parent=450"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/categories?post=450"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/tags?post=450"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}![\"\"](\"https:\/\/www.rpwoodwork.com\/blog\/wp-content\/uploads\/2009\/08\/img_1399_edited-2.jpg\" "\\"img_1399_edited-2\\"")
<\/p>\n