{"id":2570,"date":"2013-08-13T00:10:55","date_gmt":"2013-08-13T05:10:55","guid":{"rendered":"http:\/\/www.rpwoodwork.com\/blog\/?p=2570"},"modified":"2013-08-13T22:32:39","modified_gmt":"2013-08-14T03:32:39","slug":"simple-shop-made-planing-stops","status":"publish","type":"post","link":"https:\/\/www.rpwoodwork.com\/blog\/2013\/08\/13\/simple-shop-made-planing-stops\/","title":{"rendered":"Simple shop-made planing stops"},"content":{"rendered":"

\"IMG_0787_edited-2\"<\/p>\n

It pays to have a wide repertoire of options to hold wood<\/strong> in place while working on it. Here is a very simple, albeit unoriginal, device that can be used in conjunction with many of the other methods<\/a> discussed elsewhere<\/a> on this blog.<\/p>\n

The idea for these planing stops<\/strong> came to me from a version made by Veritas<\/a>. The adjustable<\/strong> feature of the Veritas is nifty, but I have an inhibition about forcefully pushing my planes toward large pieces of metal<\/strong>, even aluminum. The shop-made version is super-simple<\/strong>, super-cheap, and wooden.<\/p>\n

\"IMG_0796_edited-2\"<\/p>\n

These are made from 15″ x 1 3\/4″ x 7\/32″<\/strong> poplar with 1 \/1\/2″-long pieces of 3\/4″ dowel attached with brass screws, deeply countersunk. I spaced the dowels to accommodate the holes in my workbench.<\/strong> If I had great forethought several years ago when boring those holes, each pair in both directions would be separated by a constant distance. As it is, I had to make three<\/strong> planing stops, each with a different dowel spacing, to make full use of the hole patterns. This is not a problem because I want to have a few stops in any case.<\/p>\n

The low profile<\/strong> of these stops allows their use with thin workpieces but is still sufficient to secure thicker boards.<\/p>\n

For planing along the length of a board, two dogs<\/strong> usually suffice to secure the wood. However, vigorous planing with the scrub or jack<\/a>, working diagonally<\/a> or directly across the board, tends to dislodge it. A third stop is very helpful in these cases. Similar situations often arise in random orbit sanding, routing, and carving.\u00a0<\/strong>Workpieces that have curved edges, live-edge boards, finished drawers, and wide panels<\/strong> also can thwart the simple two-dog work holding system.<\/p>\n

The photos above<\/strong> are at the right side<\/strong> of the bench with the tail vise and wooden bench dogs. (The blue Record holdfast hole is not involved in this system.)<\/p>\n

Below<\/strong> is the hole pattern on the left side of the bench<\/strong>. Following are some of many possible configurations<\/strong> of planing stops, Veritas Bench Pups<\/a>, and bench end stops.<\/p>\n

\"IMG_0790_edited-2\"<\/p>\n

Here the planing stop is set up as a simple end stop<\/strong>, assisted by a single Pup<\/strong>:<\/p>\n

\"IMG_0789_edited-2\"<\/p>\n

Here, Pups in the front vise<\/strong> and the two stops at the end of the bench<\/strong> work with the planing stop:<\/p>\n

\"IMG_0794_edited-2\"<\/p>\n

Yet another variation<\/strong>, to put work further outward:<\/p>\n

\"IMG_0791_edited-2\"<\/p>\n

With all of this gear, something can probably be worked out to manage just about any work piece<\/strong> on the bench top:<\/p>\n

\"IMG_0792_edited-2\"<\/p>\n

Addendum:<\/strong><\/p>\n

Before settling on this version, I experimented<\/strong> building an adjustable<\/strong> version using different types of screws with the heads projecting from the tops of the dowels. The heads would then run in a T-slot<\/strong> in the stop piece. This would make the dowel positions adjustable like the Veritas version.<\/p>\n

It became too finicky for my taste, especially since I wanted to keep the stops less than 1\/4″ thick<\/strong> so they could be used for panels and other thin work pieces. The adjustable design can be done using a thicker stop piece.<\/strong> Readers may want to give it a try, but I like the thin and simple<\/strong> version.<\/p>\n","protected":false},"excerpt":{"rendered":"

It pays to have a wide repertoire of options to hold wood in place while working on it. Here is a very simple, albeit unoriginal, device that can be used in conjunction with many of the other methods discussed elsewhere on this blog. The idea for these planing stops came to me from a version […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[9],"tags":[],"class_list":["post-2570","post","type-post","status-publish","format-standard","hentry","category-jigs-and-fixtures"],"_links":{"self":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/2570","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/comments?post=2570"}],"version-history":[{"count":7,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/2570\/revisions"}],"predecessor-version":[{"id":2577,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/2570\/revisions\/2577"}],"wp:attachment":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/media?parent=2570"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/categories?post=2570"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/tags?post=2570"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}