{"id":1482,"date":"2012-01-23T02:57:57","date_gmt":"2012-01-23T07:57:57","guid":{"rendered":"http:\/\/www.rpwoodwork.com\/blog\/?p=1482"},"modified":"2013-04-19T23:05:13","modified_gmt":"2013-04-20T04:05:13","slug":"a-practical-tool-cabinet-part-4","status":"publish","type":"post","link":"https:\/\/www.rpwoodwork.com\/blog\/2012\/01\/23\/a-practical-tool-cabinet-part-4\/","title":{"rendered":"A Practical tool cabinet, part 4"},"content":{"rendered":"

\"\"<\/p>\n

Three adjustable 3\/4″ pine shelves are held with 1\/4″ plastic locking shelf supports<\/a>. The top of the drawer bank and the bottom of the case effectively make a total of five shelves. Let\u2019s take a look, starting at the top shelf.<\/strong><\/p>\n

The photos show the mere 3 inches of space above the top shelf<\/strong> on which are stored mostly chisels,<\/strong> along with some knives. To the right is a gaggle of screwdrivers. Each chisel and knife is protected in a pocket of a leather tool roll<\/strong> that has been cut lengthwise along its midline and positioned at the rear of the shelf. I know my tools well enough to recognize each one by\u00a0its handle end.<\/p>\n

The next level down<\/strong>\u00a0– the top of the drawer bank – holds small planes, scrapers, and spokeshaves. Each plane\u2019s parking space<\/strong> is delineated by a thin strip of wood held in place with just two small brads. Of course, as you would guess, these are easy to reposition. Card scrapers<\/strong> are held in a piece of 2×4 into which kerfs have been sawn along the grain.<\/p>\n

\"\"<\/p>\n

Notice the safe storage of the 24″ Starrett straightedge in a slot<\/strong> that has been table-sawn into the edge of the top shelf. In the second photo, the little keeper tab has been rotated out of the way and the straightedge is partially withdrawn. The photo, below, shows the same storage for an 18″ Starrett combination square blade. The small block<\/strong> sitting on the shelf, to the right of the yellow tape measure, is used to withdraw the straightedges<\/strong>. A rare-earth magnet is inset into the end of the block and covered with duct tape to prevent metal-to-metal scratching.*<\/p>\n

\"\"<\/p>\n

Also notice the Cortec rust inhibitor<\/a> cup, one of two in the cabinet, stuck onto the back panel under the top shelf.<\/p>\n

The next shelf, my favorite,<\/strong> holds most of my major planes<\/strong> in the same type of parking spots described above. Unfortunately, the jointer and the two jacks have to be stored along the length of the shelf and therefore are exceptions to the desirable arrangement of unblocked access to each tool. It\u2019s not much of an issue though, because I don\u2019t use the jointer,\u00a0parked in the back,\u00a0nearly as frequently as the jacks, whose parking spaces are interchangeable.<\/p>\n

\"\"<\/p>\n

The lower two shelves<\/a> hold, in no special system, all sorts of items including drill bits, tapes, mallets, and tool documentation. Here it is practically impossible to have direct access to everything, but I do prioritize access based on how frequently I use the items. The 30-drawer, plastic small-parts chest<\/strong> holds small screws and lots of little tools and parts that would otherwise tend to get misplaced.<\/p>\n

Next,<\/strong> a look at the drawers, simple and practical.<\/p>\n

*[This straightedge storage tip may seem familiar; I\u00a0submitted it to the December 2008 Popular Woodworking<\/em>.]<\/span><\/p>\n","protected":false},"excerpt":{"rendered":"

Three adjustable 3\/4″ pine shelves are held with 1\/4″ plastic locking shelf supports. The top of the drawer bank and the bottom of the case effectively make a total of five shelves. Let\u2019s take a look, starting at the top shelf. The photos show the mere 3 inches of space above the top shelf on […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[9],"tags":[17],"class_list":["post-1482","post","type-post","status-publish","format-standard","hentry","category-jigs-and-fixtures","tag-a-practical-tool-cabinet-series"],"_links":{"self":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/1482","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/comments?post=1482"}],"version-history":[{"count":4,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/1482\/revisions"}],"predecessor-version":[{"id":2278,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/1482\/revisions\/2278"}],"wp:attachment":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/media?parent=1482"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/categories?post=1482"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/tags?post=1482"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}