![\"\"](\"https:\/\/www.rpwoodwork.com\/blog\/wp-content\/uploads\/2011\/07\/img_0270_edited-2.jpg\" "\\"img_0270_edited-2\\"")
<\/p>\n<\/p>\n
A jack plane, including this one, is mostly used to true the surfaces<\/strong> of a board and dimension<\/strong> it. It follows coarser tools – the mill saw or, if substantial thickness must be removed, the scrub plane. It is followed by the jointer plane, if needed, and then the smoothing plane or other methods, such as scraping and sanding, to create a finished surface on the wood. Thus, the jack is a fairly rough tool<\/strong>. Yet it is expected to leave a surface without major defects to avoid having to remove too much wood with subsequent tools.<\/p>\n The role of the jack plane dictates its setup.<\/strong> The blade should be sharpened with a moderate camber<\/strong> – a balance between the need to remove wood quickly and leave a\u00a0decent surface. Judging the proper amount of camber comes with experience, may vary from job to job, and is most easily determined by eye, but it is important to note that a blade that is bedded at a low angle with the bevel up requires more camber<\/strong>, as judged from a 90\u030a<\/span> view, than a blade which is bedded at a higher angle with the bevel-down. Please refer to an earlier post<\/a> for a full explanation of this.<\/p>\n I prepare the blade with a primary bevel of about 30\u030a<\/span> and a secondary bevel of about 38\u030a<\/span> which, with the Veritas\u2019 12\u030a<\/span> bed, yields an attack angle of about 50\u030a<\/span><\/strong>. Going significantly higher than this makes the plane simply too hard to push through the wood for this type of work<\/strong><\/em>. A smoothing plane is a different matter in this regard. There, fewer and finer shavings are taken, so higher attack angles are practical and may be necessary to avoid tearout.<\/p>\n But wait,<\/strong> isn\u2019t the main point of a BU jack to use high attack angles and prevent tearout on difficult woods? No, not in my opinion. A jack plane does most of its job best when used diagonally across the grain<\/strong>. This makes it easier to accurately remove surface distortions and<\/em> avoid tearout, obviating high attack angles. I regularly jack plane curly woods diagonally or even nearly perpendicular to the grain.<\/p>\n For the few\u00a0occasions when a 50\u030a<\/span> attack angle creates significant tearout even with a diagonal stroke, such as with very swirly grain, it is time to employ one of the wonderfully handy advantages of a BU plane<\/strong>. The regular blade can be easily swapped for a toothed blade<\/strong> (sharpened at 40\u00b0). This magical blade can manage the most cantankerous of woods.<\/p>\n A further negative consequence<\/strong> of using a blade sharpened with too large an angle (such as 48\u030a<\/span> to produce a 60\u030a<\/span> attack angle) in the BU jack is that it becomes difficult to set the projection of the blade. It is frustratingly difficult to find the middle ground between a shaving that is too light for jack planing and an impractically deep projection, especially if the blade is starting to dull. Imagine trying to pare with a dull chisel sharpened with a 48\u030a<\/span> bevel – you\u2019ll either scrape the wood or dive into it, with little control.<\/p>\n As you near the end of the job with the jack, back off the blade projection to increase accuracy and\u00a0improve surface quality<\/strong>, thus getting the wood ready for the next stage of preparation.<\/p>\n The next post<\/strong> will discuss securing the board to the bench for jack planing, steps in setting the blade projection, and some particular features of the Veritas BU jack.<\/p>\n","protected":false},"excerpt":{"rendered":" A jack plane, including this one, is mostly used to true the surfaces of a board and dimension it. It follows coarser tools – the mill saw or, if substantial thickness must be removed, the scrub plane. It is followed by the jointer plane, if needed, and then the smoothing plane or other methods, such […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[6],"tags":[],"class_list":["post-1260","post","type-post","status-publish","format-standard","hentry","category-tools-and-shop"],"_links":{"self":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/1260","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/comments?post=1260"}],"version-history":[{"count":6,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/1260\/revisions"}],"predecessor-version":[{"id":1286,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/posts\/1260\/revisions\/1286"}],"wp:attachment":[{"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/media?parent=1260"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/categories?post=1260"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.rpwoodwork.com\/blog\/wp-json\/wp\/v2\/tags?post=1260"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}